At MT and Sons Construction, we’re committed to delivering competitive concrete/asphalt repair bids and reliable, on-time scheduling to keep your project moving forward. Explore our full list of services below and let us be your trusted partner on your next construction project.
Experienced
Reliable
Punctual
Demolition
- Saw cut existing pavement, curbs, and sidewalks to the existing depth and haul off spoils. Saw cut slurry to be vacuumed and removed. Barricades to be installed and maintained for the duration of the project.
Subgrade Preparation
- Excavation as needed for additional depth or to remove weak subgrade. Install crushed concrete flex base, fine grade to allow for proper drainage, and compact as necessary.
Concrete Repairs
- Concrete Pavement Repairs: The Standard Pavement Repair is 6” deep, reinforced with #3 rebar 18” o.c.e.w. Standard Pavement Repair is poured with 3,500 PSI concrete and a broom finish.
- Concrete Sidewalk Repairs: The Standard Sidewalk Repair is 4” deep, reinforced with #3 rebar 24” o.c.e.w. Standard Sidewalk is poured with 3,000 PSI concrete and a broom finish.
- Curb Repairs: The Standard Curb is 6” Tall, reinforced with (1) continuous #3 rebar. Standard Curb is poured with 3,500 PSI concrete and a broom finish. Can be poured Integral with Pavement or as a Curb and Gutter.
- Concrete Patch: Clean the proposed area of any loose or chugged Concrete. Apply Concrete Patch – Typically Ardex CP will be used.
- Stamped and Color Concrete: Mt and Sons can help source and install Stamped and Color Concrete. Matching as close as possible to the existing design.
Asphalt Repairs
- Full Depth Asphalt Repairs: The Standard Asphalt Repair is 6” deep. Tack and install 4” of Type “B” and 2” of Type “D” TxDot Approved Hot Mix Asphalt. Compacting in 2” Lifts.
- Asphalt Overlay: The Standard Asphalt Overlay is 2” Thick. The Surface would be cleaned with Compressed Air or a Power Broom. Tack and Install 2” of Type “D” TxDot Approved Hot Mix Asphalt. Compact.
- Asphalt Potholes: The Standard Asphalt Potholes vary in depth. The Surface would be cleaned with Compressed Air or a Power Broom. Tack and Install Type “D” TxDot Approved Hot Mix Asphalt to level the Pothole. Compact.
- Seal Coat: The Standard Asphalt Seal Coat will be cleaned with Compressed Air or a Power Broom. (2) Coats of Coal Tar Asphalt Seal Coat will be applied.
- Cement Stabilization and Overlay: The Standard Cement Stabilization will be done to a depth of 8” and the Standard Asphalt Overlay is 2” Thick. The existing Asphalt Paving will be pulverized and mixed into the subgrade. The top 2” inches will be excavated and hauled off. Then 6-8% of Cement Slurry will be mixed into the subgrade and fine graded. Once cured we will install a 2” overlay.
ADA Repairs:
- ADA Concrete/Asphalt Repairs: MT and Sons can adjust Pavement, Sidewalk, and Curb Levels to meet ADA Standards and get you back to compliance. See (Link to ADA Upgrade) for more information.
Striping
- Parking Lot Repair Striping: Upon Request we can Line Stripe Damaged or Removed Striping caused by Construction. We can also Re-Stripe the Entire Parking Lot with Pressure Washing and Brooming Options to help ensure longevity.
Tailored Bids
- Tailored Bids: Though the above repairs and services are standard – MT and Sons can tailor make any bid to meet your project needs.
